☃ PANEL BATTERY CHARGE INDICATOR 6-120V☃ . DIGITAL VOLTMETER LED TESTER DC 6-120V

. DIGITAL VOLTMETER LED TESTER DC 6-120V

✨Features:In this table, you can set the battery type with a key: lead-acid battery, lithium battery, nickel-hydrogen battery, and you can also set the battery number with a key (battery number in series).

This table is suitable for: 12V, 24V, 36V, 48V, 56V, 60V, 64V, 64V, I2V, 84V battery car, electric vehicle, battery, balance car, inverter, electric forklift, tourist car, electric vehicle, battery car, battery powered mobile equipment, etc. It can also be used for other voltage and power testing purposes.

This table can be tested to show the voltage in real time, the amount of electricity, the percentage of electricity.

Display mode optional: single display voltage; single electricity percentage display; voltage, electric cycle percentage display (default).

Two-wire system, wide supply voltage, magic test voltage: DC 6120, simple connection, convenient.

With reverse protection function, the reverse connection will not burn.

Low power flash reminder function.

Full color LED display, high quality atmosphere.

. DIGITAL VOLTMETER LED TESTER DC 6-120V

. DIGITAL VOLTMETER LED TESTER DC 6-120V

✨Specification:Power supply voltage: DC6-120 (wide range, temperament: the maximum input voltage of the crystal must not exceed 120V, otherwise there is a risk of burning

Test Voltage: DC6~120V (Automatic Decimal Point Offset)

Minimum resolution below 10: Q. 1V

Minimum resolution above 100: 1V

Power Resolution: 1%

Operating current:

Mounting hole: 47,2*27,3mm

Measurement speed: ≥ 500 ms/times

Voltage measurement accuracy: 1% (± 2)

Lead length: > 150 mm

Minimum supply voltage: 6V

Maximum supply voltage: 120V

Operating temperature:-10~ 65

Operating Humidity: 10~80% (non-condensing)

Working pressure: 80~106kPa

Exposure to sunlight: no direct exposure

✨Package List:1 * Voltage Battery Indicator;

. DIGITAL VOLTMETER LED TESTER DC 6-120V

. DIGITAL VOLTMETER LED TESTER DC 6-120V

Note:

This watch is not suitable for installation in a circuit with a xenon lamp, the xenon lamp will have thousands of high voltage volts at the time of opening, there is a chance to directly burn the watch head, if it needs to be installed, you can not install on the same line, the watch head should also be away from the xenon lamp.

User manual:

According to polarity, the red and black lines on the watch head will be connected to the positive and negative poles of the battery respectively. At this point, the watch head will immediately show the voltage in real time, electricity, percentage of electricity

The default factory value of this table:

Battery Type: Lead-acid, 12V, One Section

Display mode: power, voltage and percentage of electric cycle display;

Set the input mode:

In normal mode, press the key for a few seconds to go into settings mode, display: 1-U, each click to move to the next order of mode keys: 1-U 2-b 3-C 4-d

mode:

1-U: Voltage tuning

2-b: battery type setting

3-C: setting the battery number;

4-d: display mode setting

Voltage tuning (calibration):

In Settings mode, press the key to go to 1-U display, press the key to go to voltage calibration mode for a long time.

At this point, release the key again long press, tune the voltage up; loosen the key and press it again for a long time. The tension is finely tuned downwards. After repeatedly adjusting to the standard value, loosen the key. Wait for the screen to flicker to save the settings and exit the settings mode.

Selection of battery type:

In settings mode, press the button to go to 2-b display, press the button to go to battery type selection mode for a long time, each "click" will switch one battery type, battery type cycle switching order: 1.2V _ 2V _ 3,3V _ 3,7V _ 12V

1.2V: On behalf of Ni-MH battery, single voltage is 1.2V.

2 V: represents lead-acid battery, single voltage is 2 V

3,2V: represents lithium iron phosphate battery, single section voltage is 3,2V 3,7V: represents lithium polymer battery, single section voltage is 3,7V

12V: represents lead-acid battery, single voltage is 12V

When switching to the appropriate battery type, immediately release the button, wait for the flash settings on the screen and exit the settings mode.

. DIGITAL VOLTMETER LED TESTER DC 6-120V

. DIGITAL VOLTMETER LED TESTER DC 6-120V

Setting the battery number:

In Settings mode, press the button to go to 3-C display, long napa in battery number setting mode, then release the button and press the long press again, the value will jump; loosen the key and press it again for a long time, the value will jump down and repeatedly adjust the number of batteries.

Wait for the screen flash settings and exit the settings mode

The range of adjustable “number of segments” for different types of batteries is as follows:

Lead-acid battery 12 V: 1-10

Lithium battery 3,7 V: 2-28

Lithium-ion battery 3,2 V: 2-32

Lead-acid battery 2 V: 3-60

Ni-MH 1,2 V Battery: 10-70

Display Mode Settings:

In Settings mode, press the button to go to 4-d display, press the button for a long time to go to display mode settings.

At this point, release the button, each “click” switches the display mode: V _ o

. DIGITAL VOLTMETER LED TESTER DC 6-120V

. DIGITAL VOLTMETER LED TESTER DC 6-120V