Stalowy blok gazowy o niskim profilu Śruba dociskowa Standardowa lufa o średnicy 0,75 cala. Blok gazowy 223 M4 / AR15
Specyfikacja:
1. Średnica: 0,75 cala
2. Długość: 255mm
3. wysokość: 344mm
4. Waga (netto): 30g
5. Zainstaluj na zwykłej beczce 0,75 cala i standardowej rurze gazowej, wysokiej jakości stal w trwałym czarnym matowym wykończeniu
6. Regulowany blok gazowy luneta do montażu taktycznego jelca blok gazowy myśliwski ar .750 Blok gazowy beczki ar 15/M4/.223
Pakiet:
1 zestaw bloku gazowego
Steel Gas Block Low Profile Set Screw Standard Barrel 0.75 Inch Diameter .223 M4/AR15 Gas Block
Specification:
1.Diameter: 0.75 inch
2.Length: 255mm
3.height: 344mm
4.Weight (net): 30g
5.Install onto 0.75 inch regular barrel and standard gas tube ,High quality steel in durable black matte finish
6.adjustable gas block scope mount tactical handguard hunting gas block ar .750 Barrel gas block ar 15/M4/.223
Package:
1 set Gas Block
Zainstaluj blok gazowy, rurę gazową i śruby ustalające | Install Gas Block, Gas Tube, & Set Screws
- Części: blok gazowy, rura gazowa, śruby dociskowe.
- Narzędzia: klucz imbusowy lub klucz imbusowy.
- Parts: Gas Block, Gas Tube, Set Screws.
- Tools: Allen Key or Allen Wrench.
Zbierz rurę gazową, blok gazowy i śruby dociskowe. Najpierw włóż koniec rury gazowej z otworem na wałek do bloku gazowego. Jest ciasno dopasowany; może pomóc smar. Wciśnij rurkę do bloku, aż otwór w rurce zrówna się z otworem kołka rolki w bloku, jak pokazano po lewej stronie. Wsuń blok gazowy na lufę i pozwól, aby drugi koniec rury przeszedł przez otwór rury gazowej (i otwór w mocowaniu łoża, jeśli dotyczy) do komory zamkowej.
Collect the gas tube, gas block, and set screws. First, insert the end of the gas tube with the roll pin hole into the gas block. It is a tight fit; lubricant may assist. Press the tube into the block until the hole in the tube aligns with the roll pin hole in the block, as shown left. Slide the gas block onto the barrel, and allow the other end of the tube to feed through the gas tube hole (and hole in the handguard attachment, if applicable) into the upper receiver.
Chwyć śruby ustalające z osprzętu bloku gazowego i wkręć je ręcznie do bloku gazowego za pomocą klucza imbusowego lub klucza imbusowego, mocując blok do lufy. Czyniąc to, dwukrotnie sprawdź, czy otwór kołka walcowego dla kołka łączącego blok gazowy z beczką jest wyrównany z wycięciem na kołek w samej beczce. Powyżej dziura jest zakreślona na czerwono.
Grab the set screws from the gas block hardware and thread them hand-tight into the gas block with the Allen key or Allen wrench, securing the block to the barrel. While doing so, double-check the roll pin hole for the gas block-to-barrel pin is aligned with the cut-out for the pin in the barrel itself. The hole is circled in red above.
Sprawdź wyrównanie rurki, zainstaluj wałek bloku gazowego | Check Tube Alignment, Install Gas Block Roll Pin
- Parts: Gas Block Roll Pin.
- Tools: 5/32" Punch, Gunsmith Hammer, Gas Tube Alignment Tool or BCG(Bolt Carrier Group).
- Części: wałek do wałka bloku gazowego.
- Narzędzia: dziurkacz 5/32", młot rusznikarski, narzędzie do ustawiania rur gazowych lub BCG (grupa nośna śrub).
Grab the gas block roll pin and 5/32" punch with gunsmith hammer. Once you seat that gas block roll pin, it ain't comin' out without a fight. Before you begin tapping it into the gas block, double-check alignment of the gas tube with the upper receiver. This can be accomplished with the Gas Tube Alignment Tool included in the Wheeler Armorer's Kit. Or, you can grab your BCG and charging handle, install the pair into the receiver, and check alignment via the handle and gas key on the carrier.
Chwyć wałek bloku gazowego i przebijak 5/32" młotkiem rusznikarskim. Gdy już osadzisz ten wałek bloku gazowego, nie wyjdzie on bez walki. Zanim zaczniesz wbijać go w blok gazowy, sprawdź dokładnie wyrównanie rury gazowej z górnym odbiornikiem. Można to osiągnąć za pomocą narzędzia do ustawiania rury gazowej zawartego w zestawie Wheeler Armorer's. Możesz też chwycić BCG i uchwyt przeładowania, zainstalować parę w komorze zamkowej i sprawdzić wyrównanie za pomocą uchwytu i klucz gazowy na nośniku.
Po sprawdzeniu wyrównania rury gazowej i odbiornika możesz zacząć wbijać kołek blokujący gaz na miejsce. Aby zapobiec uszkodzeniu wykończenia lufy, umieść kołek w otworze i uderz go bezpośrednio polimerową końcówką młotka rusznikarskiego. Po częściowym osadzeniu kontynuuj wbijanie kołka na miejsce za pomocą przebijaka 5/32". Kołek jest dłuższy niż blok gazowy i wycięcie na beczkę; upewnij się, że wystaje na równe długości po obu stronach bloku.
Once you've verified alignment of the gas tube and receiver, you may begin tapping the gas block roll pin into place. To prevent marring the finish on the barrel, seat the pin atop the hole and tap the pin directly with the polymer end of your gunsmith hammer. Once partially seated, continue tapping the pin into place with the 5/32" punch. The pin is longer than the gas block and barrel cut-out; ensure it protrudes at equal lengths on both sides. of the block.
Włóż kołek do rurki gazowej | Insert the Gas Tube Roll Pin
- Części: wałek do rurki gazowej.
- Narzędzia: dziurkacz 3/32", młot rusznikarski, szczypce (opcjonalnie).
- Parts: Gas Tube Roll Pin.
- Tools: 3/32" Punch, Gunsmith Hammer, Pliers (optional).
Jeśli zainstalowałeś własne LPK w dolnym odbiorniku, witaj ponownie! Sworzeń do rurki gazowej ma mniej więcej taki sam rozmiar i szerokość jak trzpień zatrzaskowy i tak, może to być uciążliwe. Tym razem instalujesz go na zaokrąglonej powierzchni. Pomocne jest ponowne umieszczenie odbiornika poziomo w imadle dla tego. Zbierz przebijak 3/32", młotek rusznikarski i wałek do ciasta i wbij go na miejsce. Nie spiesz się, będzie z tobą walczyć. Po zainstalowaniu kołek powinien być wyrównany po obu stronach bloku gazowego.
If you installed your own LPK in your lower receiver, then welcome back! The gas tube roll pin is about the same size and width as the bolt catch pin and yes, it can be a pain. This time, you're installing it on a rounded surface. It helps to re-seat your receiver horizontally in your vise for this one. Collect the 3/32" punch, gunsmith hammer, and roll pin and tap it into place. Take your time, it will fight you. Once installed, the pin should be flush on both sides of the gas block.